Technical manual, Software, CAD data
PLC
Software
Series Common
-
2024.01.12 Update
PLC programming software compatibility table
SJ series requires Ver 5.1 or later.
DL05 requires Ver 2.4a or later.
DL06 requires Ver 4.0 or later.
D2-263 does not support DirectSOFT5, but supports KPP.
D2-250-1 requires Ver 4.0 or later.
D2-260 requires Ver 4.0 or later.
D2-265 requires Ver 5.1 or later.
SU-5M requires Ver 2.4a or later.
The SA/SR series requires a host link unit (E-03DM).
SA-20 and SR-20 are not compatible with DirectSOFT5
SG-8 requires Ver2.9 or later. -
Kostac PLC Programming Software Setup(V1_6_15_0)(73 MB)
2024.10.01 Update
Downloaded file is Zip file. After unzipping, please open
'KostacPLCProgrammingSoftware_Setup (V1.6.15.0).exe'
And refer to Installation Guide (present in the same folder as the exe) before installing the software.
countermeasure to ensure integrity of project file have been applied on V1.6.12.0.
If you are using a project file saved with a version older than V1.6.12.0, we recommend that you save it again with a version later than V1.6.12.0 for greater safety.
Once saved project file cannot be opened in versions older than V1.6.12.0.
Therefore, project files that can be opened in older versions are automatically backed up.KPP(KostacPLCProgrammingSoftware)tool [It can be downloaded for free.]
-
This file, when used without a keycode, will install the latest version of DirectSOFT100, the "free" version of DirectSOFT5. DirectSOFT100 gives you the same features as the full version of DirectSOFT5 but allows only 100 Words of ladder code to be downloaded to the PLC. Use the DirectSoft5 keycode you received when purchasing DirectSOFT5 to install the latest release of PC-DSOFT5, the full version of DirectSOFT5.
-
JX Programming Software Ver3.40 J1.40(41 MB)
2024.11.06 Update
Downloaded file is Zip file. After unzipping, please open.
Direct Logic205 Series
-
2015.06.25 Update
In the case of the D2-02PM use, the setting such as the kind of the pulse, the speed limit is necessary by this application. It is the file of the ZIP form. I carry out "D2-02PMTool.exe" after thawing, and, please install it.
Rev2.0.0.2
-
2014.08.22 Update
This Manual describes the configuration procedures (commands and setting registers) for the D2-02PM,Two Axis Motion Control Module that is part of the DL205 series. It also explains how to connect and use the D2-02PM with external devices.
Rev1.00
-
D2-DEVMSTR Configuration Tool(14 MB)
2023.03.06 Update
Ver 1.5.2.0
-
Firmware
KOSTAC SJ-ETHER Series
-
Firmware_for_SJ-ETHER_V2.810(472 KB)
2023.03.15 Update
We published firmware along with updating of SJ-ETHER(V2.800 ⇒ V2.810).
Please refer to PDF for the details of the version upgrade. -
SJ-ETHER firmware Version Up History(68 KB)
2023.03.15 Update
-
Firmware_for_SJ-ETHER_V2.800(471 KB)
2023.03.15 Update
It's an older version of firmware.
-
2024.09.30 Update
Manual
KOSTAC SJ-ETHER Series
-
SJ- ETHER user's manual(11 MB)
2020.04.15 Update
User's manual for SJ-ETHER Series
【Updated details】
P.2-13 Table of special relays ⇒ Modified details of SP12 TERM-RUN, SP16 TERM-STOP
P.4-7 ②Port3 (Ethernet communication) ⇒ Added EtherNet/IP to Item column in the table.
P.4-10 CC-Link IEF Basic⇒Added the Note describing connectable units of slave with depending on each firmware version.
P.4-37 CC-Link IEF Basic communication ⇒ Added the Note describing connectable units of slave with depending on each firmware version.
・Modified error and layout of sentence, figure and table in entire sectionsRev.102
-
-
-
SJ-ETHER Firmware Update Manual (Update Procedure)(477 KB)
2024.01.12 Update
SJ-ETHER Firmware Update Manual
KOSTAC safety AZ-C1
-
Ver2.5
Direct Logic05/06 Series
-
DL05 Micro PLC User Manual 6th Ed.Rev.C(Vol 1 of 2)
-
DL05 Micro PLC User Manual 6th Ed.Rev.C(Vol 2 of 2)
-
DL06 Micro PLC User Manual 3rd Ed.Rev.C (Vol 1 of 2)
-
DL06 Micro PLC User Manual 3rd Ed.Rev.C (Vol 2 of 2)
-
-
-
All DL05/DL06 Options Modules 7th Ed.Rev.A
-
D0-DCM Data Communications Module 2nd Ed.
-
DL05/DL06 DeviceNet Slave Module 1st Ed.Rev. A
-
Counter I/O Modules 2nd Ed.Rev. D
-
Hx-CTRIO(2) Chinese manual(3 MB)
2020.02.12 Update
Chinese user's manual for H0-CRTIO(2),H2-CTRIO(2),H4-CTRIO and T1H-CTRIO
-
Profibus Slave Communications Module 1st Ed.
Direct Logic205 Series
-
DL205 User Manual 4th Ed.Rev. B (Vol 1 of 2)
-
DL205 User Manual 4th Ed.Rev. B (Vol 2 of 2)
-
DirectLogic 205 Series Additional Manual for D2-265(2 MB)
2013.09.27 Update
This manual mentions various features that were added for D2-265 CPU only.
Rev1.00
-
-
2013.09.27 Update
This manual shows Motion control module of D2-MLINK that How to communicate to MECHATROLINK-Ⅱ modules such as servo system. It is include module setting(command and configuration register)
Rev1.00
-
2014.08.22 Update
This Manual describes the configuration procedures (commands and setting registers) for the D2-02PM,Two Axis Motion Control Module that is part of the DL205 series. It also explains how to connect and use the D2-02PM with external devices.
Rev1.00
-
DL205 Analog Modules 7th Ed.Rev.B
-
Counter Interface 2nd Ed. Rev. A
-
Data Communication Module 2nd Ed.
-
Handheld Programmer 2nd Ed.Rev. A
-
Remote Master/Remote Slave 1st Ed. Rev. A
-
Ethernet Communications Module 3rd Ed.Rev. C
-
Ethernet Remote Master 2nd Ed.Rev. A
-
Ethernet Base Controller 3rd Ed.Rev.A
-
Counter I/O Modules 2nd Ed.Rev. D
-
Hx-CTRIO(2) Chinese manual(3 MB)
2020.02.12 Update
Chinese user's manual for H0-CRTIO(2),H2-CTRIO(2),H4-CTRIO and T1H-CTRIO
-
Profibus Slave Base Controller 1st Ed.Rev. A
-
F2-DEVNETS-1 Installation and Use 1st Ed.
-
Smart Distributed System CPU
-
F2_D2-DEVMSTR_SPEC-November-11-2019(460 KB)
2019.11.11 Update
F2_D2-DEVMSTR_SPEC
Revised at November 7 2019
-
Direct Logic305 Series
-
DL350 User Manual 2nd Ed
-
DL330/340 User Manual 1st Ed. Rev. D
-
DL305 Analog Modules 3rd Ed.
-
Data Communication Module 2nd Ed.
-
Data Communication Unit 1st Ed.Rev. A
-
High Speed Counter 1st Ed.Rev. A
-
Handheld Programmer 1st Ed. Rev. B
-
Installation and use of F3-OMUX-1/2/3
-
Installation and Use of F3-PMUX-1
Direct Logic405 Series
-
DL405 User Manual 4th Ed.Rev. A
-
-
DL405 Analog Modules 5th Ed.Rev.A
-
Data Communications Module 1st Ed.Rev. A
-
High Speed Counter 1st Ed. Rev. A
-
Interupt Input Module 1st Ed. Rev. A
-
Remote I/O 1st Ed. Rev. C
-
Slice I/O Master and Slaves 1st Ed. Rev. A
-
Handheld Programmer 1st Ed. Rev. A
-
Ethernet Communications Module 3rd Ed.Rev. C
-
Ethernet Remote Master 2nd Ed.Rev. A
-
Ethernet Base Controller 3rd Ed. Rev. A
-
Counter I/O Modules 2nd Ed.Rev. D
-
Hx-CTRIO(2) Chinese manual(3 MB)
2020.02.12 Update
Chinese user's manual for H0-CRTIO(2),H2-CTRIO(2),H4-CTRIO and T1H-CTRIO
-
Four Loop Temperature Controller
-
Magnetic Pulse Input CoProcessor
-
16-loop PID CoProcessor
-
Modbus Master
-
Modbus Slave
-
Shared Data Network CoProcessor
-
SDS Network Master
JX Series
-
JX-Series-User-E-M-_Rev.4.00(15 MB)
2024.11.06 Update
Remote I/O Module EPSK Series
-
EPSK_Users_Manual (Japanese language)(7 MB)
2024.09.19 Update
-
2024.09.30 Update
EPSK Series
EtherNet/IP Target EDS files
Terminator I/O
-
Counter I/O Modules 2nd Ed.Rev. D
-
Hx-CTRIO(2) Chinese manual(3 MB)
2020.02.12 Update
Chinese user's manual for H0-CRTIO(2),H2-CTRIO(2),H4-CTRIO and T1H-CTRIO
-
Profibus DP Base Controller 1st Ed.Rev. A
-
DeviceNet Base Controller 1st Ed.
-
Ethernet Base Controller 2nd Ed. Reb. B
-
MODBUS Base Controller 1st Ed.
-
DirectLogic Remote I/O Base Controller 1st Ed.
SA SR
-
-
-
-
-
Stage Type Programming Method and Data Process Instructions(7 MB)
2023.10.26 Update