How Can We Help?
- Calendar accuracy
- Coin battery consumption is fast
- Migrating data registers(kpp)
- Modbus/RTU communication (Master)
- Mode SW
- Power outage retention
- RX/WX instructions
- USB/Serial conversion cable
- Using a Password
- What is a "Stage Type Programming" ?
-
DirectLogic05/06
-
AZ-C1
-
SJ-ETHER
- Connection with SJ series personal computer
- Difference between SJ-xxxE-D and SJ-xxxEP-D
- Gateway Mode
- How to use analog type CPU & I/O
- How to use C0-04THM/RTD
- SJ Series Replacement
- SJ-Ether CC-Link IEF Basic Settings
- SJ-Ether EtherNet/IP communication
- SJ-Ether Modbus/TCP communication（master）
- SJ-Ether Modbus/TCP communication（slave）
-
Programming Software
-
KPP
-
Direct SOFT
-
-
DirectLogic205(D2,SZ)
- Analog configuration volume
- Connection with D2 series personal computer.
- D2 / SZ series CPU replacement
- D2 / SZ series CPU replacement precautions
- D2 32/64points I/O terminal block
- D2-263 Connection with Mitsubishi Electric HMI's
- D2-263 does not run
- ECOM cannot be recognized by NetEdit
- H2-CTRIO settings
- Modbus/TCP communication (master)
- Setting up analog modules
- SZ series alternative
-
SU(D4)
- BATT LED blinking / RB-7 replacement
- Connection with SU series personal computer
- Current Source Input
- D4-454 User's Manual
- ECOM cannot be recognized by NetEdit
- Memory cartridges
- Modbus/TCP communication (master)
- SU series 64 points I/O precautions
- SU series CPU replacement (Direct SOFT)
- SU series CPU replacement (KPP)
- SU series module position change
- SU series PWR, RUN LED blinking
- SU(D4) 32/64points I/O terminal block
- U-01Z/U-01PM/U-11PM FW Version
- U-8ADC-1 Jumper settings
-
SA/SR
-
Other
-
Update old systems
-
JX
- Calendar function
- Driver installation failed
- How to connect HMI (Touch Panel)
- How to use On Board AD/DA of JX-BASIC-EX2
- JX-BASIC-EX2 Accessories
- Modbus Address
- Power failure retention function
-
I want to do ...
-
USB Connection
-
Compatibility
-
SUNX SFL
- Cable flexibility
- Connect totem-pole output to the PLC
- Encoder cable extension
- Encoder, To use it outdoors
- Encoders option
- How to use Line Driver
- Open collector output cable length
- OUTZ position
- Parallel connection of open collector outputs
- Parallel connection of totem-pole outputs
- The model number has a 4-digit number at the end of the model number
- Totem-pole output cable length
-
TRD-SR/SHR
-
TRD-N/NH
-
TRD-NA
-
TRD-S/SH
-
TRD-2E
-
TRD-J
-
TRD-G/H
-
TRD-D/E
-
TRD-KL
-
TRD-GK
-
TRD-Sx/Rx
-
NIDEC RE1 RE2
-
TRD-GKL
-
Touch Panel
- Backup battery replacement
- DSUB connector fixing screw
- EA-MG-PGM-CBL is not working
- KOMATSU's HMI
- Programming Software and Download cables
- To open previously created screen data
-
GC-53/55/56
-
GC-73/76
-
EA7
-
GC-A24/25/26
-
SCA2(Drawing Software)
-
Panel Computer
-
Visual Scope
- APS-1*-*T replacement
- APS-13-7TH replacement
- APS-14-15N cable wire color
- APS-30/31-*T replacement
- APS4-12S mounting hole dimensions
- APS4-12S/M output type identification method
- APT-123 replacement
- Cable flexibility
- Parallel connection (OR) / Series connection (AND)
- Parallel connection of open collector outputs
- Products with a 4-digit model number at the end
- Replacement of DC voltage output type
-
KCV
-
KCX
-
KCN
- KCN-*SR-* replace
- KCN-*ST-* replace
- KCN-*WR-* replace the dual-preset setting
- KCN-*WR-* replace the single-preset setting
- KCN-*WT-* replace the dual-preset setting
- KCN-*WT-* replace the single-preset setting
- KCN-4SR-＊ replace the timer operation
- KCN-4ST-* replace the timer operation
- KCN-A*SR-* replace
- KCN-A*ST-* replace
-
Other counters
-
KCY
-
Chokotei
- Articles coming soon
-
OnSinSensor
- Acceleration measurement value
- Application developed in-house acquires the data
- How to check the measurement data
- Link to application software developed in-house
- Power Supply
- The detected acceleration
-
sensor
-
Logger
-
Software
-
PonzukeBox
- Cable bending resistance
- Factory Settings
- Gain adjustment
- Moment of inertia ratio
- Output pulse number and motor rotation speed (E-gear Ratio)
- Peripheral devices
- Servo Reducer
- What is PUU?
-
CN1
-
Modbus Communication(RS-485)
-
Electronic cam
-
Alarms and countermeasures
-
How to control
- Absolute system
- Control DIO through communication
- Cylinder reciprocating
- Feed by fixed length using an external trigger
- Full-closed loop control
- Handshake the operation and completion of PR mode
- Position control using external pulses
- Position or Speed control mode: Torque limit
- Press-fitting operations
- Rotary axis position command (Index Control)
- Set the stop position as the origin
- Speed control with external analog signal
- Speed mode: 4th speed or more
- Speed mode: Stop the motor
- Torque mode: Speed limit
-
KSD-Soft
Popular Articles
Newest Articles
Recently Updated Articles